Editing MetBox (Meteorological Box)

[[Category:technology]]
Status: Contents not yet checked by product owner

== Description ==
The MetBox is a low cost low maintenance and high accuracy package to measure reliably the main essential meteorological parameters such as wind speed and direction, air temperature, humidity and atmospheric pressure. 

Measurements are sampled by a microcontroller, then encoded and transmitted. The transmission channel used varies depending on the device version. 

=== Version v0 ===
The v0 was developed in August 2024. This revision included:

* An Arduino Micro to sample the measurements
* The Calypso ULP Standard wind sensor, set to uart interface
* BMP280 and SHT40 pressure and humidity sensors, integrated in an [https://shop.m5stack.com/products/env-iv-unit-with-temperature-humidity-air-pressure-sensor-sht40-bmp280?srsltid=AfmBOopkrKIIzp_szCCjrA_S9ohKOxDaMtbRlNIdqRX2rjFj80QTIxMd ENV IV]
* Two communication interfaces were implemented
** A USB interface, extended with an active extender (for monitoring and firmware update)
** A Serial RS485 interface
* A POM housing
* Radiation guards made from PLM print material, with an additional coatin
<gallery mode="packed-hover" heights="350">
File:MetBox.png|MetBox v0
</gallery>
[[File:V0 cutView.jpg|center|thumb]]
[[File:V0 exploded.jpg|center|thumb|Metbox v0 exploded view|330x330px]]

=== Version v1 ===
Development of the version V1 was completed in May 2025. The changes introduced were:

* The housing was changed. This version is shorter than the previous,the electronics compartment is, however, wider.
* The housing is meant to be printed and assembled with M4 screws for stability. 
* Pow input is connected via a [https://de.rs-online.com/web/p/industrie-automation-steckverbinder/8771154 M12 - 5 wire - panel mount] connector. 
* Sensors are interfaced with an i2c bus. 
* A [https://wiki.seeedstudio.com/Grove_LoRa_E5_New_Version/ Grove - Wio-E5] (uart) is used for data transfer through '''LoRaWAN''' with the  [https://www.taoglas.com/product/860-928mhz-ism-lora-compact-flexible-pcb-antenna/ FXP890.07.0100C] antenna. 
* The controller is an Arduino nano IoT 33. 
[[File:A-0040A page-0002.jpg|center|thumb]]
[[File:A-0041A page-0002.jpg|center|thumb|Metbox bottom assemby.]][[File:V1B.jpg|center|thumb|250x250px|Metbox, v1. ]]

=== Circuit schematic ===
[[File:Metbox v1 circuit.jpg|center|thumb]]

== Measurement Parameters (extern) ==
{| class="wikitable"
!SENSOR PARAMETER
!MANUFACTURER
!MODEL
!INTERFACE
!UNIT
!RANGE
!ACCURACY
!Registry UUID
|-
|AIR TEMPERATURE
|Sensirion
|[https://sensirion.com/products/catalog/SHT40 SHT40]
|i2c
|°C
| -40-125
|0.2
|
|-
|ATMOSPHERIC PRESSURE
|Bosch
|[https://www.bosch-sensortec.com/products/environmental-sensors/pressure-sensors/bmp280/ BMP280]
|i2c
|hPa
|300-1100
|~ ±1 hPa (abs)
± 0.12 hPa (relative)
|
|-
|HUMIDITY
|Sensirion
|[https://sensirion.com/products/catalog/SHT40 SHT40]
|i2c
|%
|0-100
|1.8
|
|-
|WIND SPEED
|Calypso Instruments
|[https://calypsoinstruments.com/shop/ultra-low-power-ultrasonic-wind-meter-ulp-standard-6?category=2#attr=76,71,65 ULP Standard]
|uart / i2c
|m/s
|0.5 - 45
|± 0.3
|
|-
|WIND DIRECTION
|Calypso Instruments
|[https://calypsoinstruments.com/shop/ultra-low-power-ultrasonic-wind-meter-ulp-standard-6?category=2#attr=76,71,65 ULP Standard]
|uart / i2c
|° (degrees)
|0-359
|± 1
|
|}
'''Note:'''

Wind directions shown are '''where the wind comes from''', according to the standard meteorological convention (e.g., 0° = wind from the North, 90° = from the East, etc.).

== Technical Requirements for Operators (extern) ==

=== Where to install the instrument on the ship? ===
Preferably on the main mast or at a high place where the air stream is not obstructed.

=== What power supply does the instrument require? ===

==== Version v1 ====
6 - 21 VDC 

Power consumption < 200 mW (unoptimized)

The connector selected is a [https://de.rs-online.com/web/p/industrie-automation-steckverbinder/8771154 m12 5 pole, panel mounted]. The pinout is (also described in detail in the Circuit schematic section):
{| class="wikitable"
|+
!Pole
!Color
!Description
|-
|1
|brown
|Not used
|-
|2
|white
|vcc
|-
|3
|blue
|gnd
|-
|4
|black
|can H (planned)
|-
|5
|grey
|can L (planned)
|}

=== What is the size of the instrument? ===
28 x 11 x 11 cm

==== Version v1 ====
20 x 11 x 11 cm

=== Water proofness ===
Splash proof

=== What maintenance does the instrument require? ===
System cleaning of the system once a year or before, if needed. 

=== How will data be transferred? ===

==== Version v0 ====
Serial (RS485)

==== Version v1 ====
LoRaWan

Wifi, Bluetooth planned

uart planned

=== Prototypes ===
How many prototypes will be available for testing by operators by end of 2024? How many will be available by end of 2025?
{| class="wikitable"
!
!2024
!2025
|-
|'''Prototypes'''
|4
|tbd
|}

{| class="wikitable"
|+
!Prototype #
!Available for testing
!Start date
!End date
!Maximal usage time
|-
|1
|Yes
|Jul. 2024
|Oct. 2024
|tbd
|-
|2 - 4
|No
|Oct. 2024
|tbd
|tbd
|}

=== Costs ===
Material costs ~500 EUR

== Technichal Details ==

== Collaboration(s) ==

== Use Case(s) involvement ==
Solely [[Use Case 4 - Sailors]]

== Development status ==

=== [[Technology Readiness Level]] ===
'''7'''

=== Expected date for market readiness ===
Not clear yet

=== Commercial availability ===

=== Autonomous operation ===

=== OSBK Interface ===
OSBK board is not yet implemented as not available (27.08.2024).

The housing, with all wiring prepared, sensors connected and tested, was supplied for OSBK integration (19.06.2025)

=== Up-scaling ===

== Data ==

=== Data transmission ===
Version v1

Data is encoded to hexadecimal and sent via LoRaWan to a TTN project. Inside the TTN console, a javascript payload formatter decode the data and asigns the o2a tags, following [[LoraWan Data Flow|lorawan data flow]].

=== Data handling ===

=== Data visualisation ===

=== Data business models ===

=== O2A Registry UUI ===

== How to install? ==
A [https://de.rs-online.com/web/p/sensor-und-aktor-kabel/8919444 m12, 5 pole female connector] can be attached to provide power.

A tube can be attached to the bottom part and secured with 6x M4 screws mounted radially. The opening allows a tube with a max OD of Ø45 mm and min ID of Ø20 mm. A bushing can be used to increase stability, in addition to the tube. [[File:A-0042.jpg|center|thumb]]

== How to operate? ==
If a LoRaWan coverage is avaliable, the device is plug and play.

== How to calibrate? ==

== Further details ==
 Product owners: Jochen Horstmann and Alejandro Ordóñez (HEREON)